| ADI ADP2102/1653 LED驱动方案 |
| |
| 作者：未知 来源：ADI 点击数：80 更新时间：2008-7-24 |
|
您可以添加到网摘 让更多人关注此文章：
ADP2102低静态电流降压式DC/DC变换器和ADP1653 白色LED闪光灯驱动器都属于电源管理集成电路(IC)，它们适合于便携式手持应用，例如无线手机、数码照相机和其它应用。这两款芯片以高达95%的电源效率显著延长了电池寿命，并且配合节能模式在轻负载条件下降低了开关频率。此外，它们还提供过压和欠压锁定以及软启动功能，有助于减少或消除启动期间电池过度放电或启动电流过冲造成的损害影响。当射频（RF）发射期间放大器的电流突然增加时，ADP1653提供一种独特的功能——当在RF传输时，Tx masking启动，降低闪光灯LED的消耗电流。这两款芯片在小尺寸封装中实现了这些附加的性能。本文介绍了ADP2102和ADP1653的主要性能，应用电路以及ADP1653闪光LED驱动器评估板中主板和子板的详细电路图。
1．
The ADP2102 is a synchronous step-down dc-to-dc converter that converts a 2.7 V to 5.5 V unregulated input voltage to a lower regulated output voltage with up to 95% efficiency and 1% accuracy. The low duty cycle capability of the ADP2102 is ideal for USB applications or 5 V systems that power up submicron subvolt processor cores. Its 3 MHz typical operating frequency and excel-lent transient response allow the use of small, low cost 1 μH inductors and 2.2 μF ceramic capacitors. At medium-to-high load currents, it uses a current mode, pseudofixed frequency pulse-width modulation to extend battery life. To ensure the longest battery life in portable applications, the ADP2102 has a power save mode (PSM) that reduces the switching frequency under light load conditions to significantly reduce quiescent current.
The ADP2102 is available in both fixed and adjustable output voltage options with 600 mA maximum output current. The preset output voltage options voltage are 1.875 V, 1.8 V, 1.5 V, 1.375 V, 1.25 V, 1.2 V, 1.0 V, and 0.8 V. The adjustable voltage option is available from 0.8 V to 3.3 V. The ADP2102 requires only three external components and consumes 0.01 μA in shutdown mode.
The ADP2102 is available in an 8-lead LFCSP package and is specified for the −40 °C to +85 °C temperature range.
ADP2102主要特性：
Input voltage range: 2.7 V to 5.5 V
600 mA maximum load current
95% efficiency
Low duty cycle operation
Only 3 tiny external ceramic components
3 MHz typical operating frequency
Fixed output voltage from 0.8 V to 1.875 V
Adjustable output voltage up to 3.3 V
0.01 μA shutdown supply current
Automatic power save mode
Internal synchronous rectifier
Internal soft start
Internal compensation
Enable/shutdown logic input
Undervoltage lockout
Current limit protection
Thermal shutdown
Small 8-lead, 3 mm × 3 mm LFCSP package
ADP2102主要应用：
USB powered devices
WLAN and gateways
Point of loads
Processor core power from 5 V
Digital cameras
PDAs and palmtop computers
Portable media players, GPS
电型应用电路：
图1。 ADP2102-FXD (0 mA ≤ ILOAD ≤ 300 mA)
图2。 ADP2102-FXD (0 mA ≤ ILOAD ≤ 600 mA)
EVALUATION BOARD SCHEMATICS
图3。ADP2102-1.2-EVALZ 电路图， VOUT = 1.2 V
图4。ADP2102-EVALZ 电路图， VOUT = 3.3 V
2．
ADP1653闪光LED驱动器
The ADP1653 is a very compact, high efficiency, high power, camera flash LED driver optimized for cellular phones. The high efficiency and dynamic LED current control of the device improve flash brightness and picture quality in dimly lit environments. Efficiency peaks at 92% and is higher than charge pump solutions over the Li-Ion battery range.
The device has a dual-mode interface that is configurable to 2-bit logic or an I2C interface. The indicator and high power LED currents are programmable with external resistors or through the I2C interface. To maximize overall flash brightness, the ADP1653 offers an input to reduce flash LED current in less than 50 μs, referred to as the Tx mask. Tx masking reduces battery stress by scaling back flash LED current during an RF transmission.
The ADP1653 solution requires only four external components in I2C mode and fits in a 6.4 mm × 7.2 mm space. The part inte-grates multiple safety features such as soft start, flash timeout, output current limit, thermal protection, and overvoltage protection.
The ADP1653 operates over the −40°C to +125°C junction temperature range.
ADP1653主要特性：
Small 6.4 mm × 7.2 mm solution
2.2 μH power inductor
92% peak efficiency
Tx masking within 50 μs
2.1 A, 12 V power switch
Pin-selectable interface: 2-bit logic or I2C
Programmable flash and torch current
Up to 200 mA in torch mode
Up to 500 mA in flash mode
Programmable indicator LED current up to 20 mA
Programmable timer register: up to 820 ms flash timeout
2.75 V to 5.5 V input voltage range
Low noise, 1.2 MHz PWM operation
Safety features
Interrupt output pin
Fault condition register Short-circuit protection
Output overvoltage protection
Thermal overload protection
Integrated current limit and soft start
Small 3 mm × 3 mm, 16-lead LFCSP footprint
interface
Jumpers for measurement of flash LED current and inductor current
TxMask for changing flash current on the fly
Evaluation software included
图7。评估板中的子板电路图
图8。评估板中的主板电路图
ADP1653应用：
Camera-enabled cellular phones, smart phones
Digital still cameras, camcorders, PDAs
图5。ADP1653详细方框图
图6。ADP1653应用电路图
ADP1653闪光LED驱动器评估板
ADP1653 Flash LED Driver Evaluation Board
The evaluation system is composed of a motherboard and a daughterboard. The motherboard provides the I2C signals from the computer USB port and generates the I/O voltages and digital high and low signals for the daughterboard. For temperature measurement, the daughterboard can be either plugged directly into the motherboard or connected to the motherboard via the ribbon cable provided with the evaluation kit.
The motherboard features a 3.3 V regulator and a 1.8 V regulator. The jumpers on the bottom left of the motherboard set the VIC voltage, which is the I2C voltage for the control pins. Users can choose among the 1.8 V, 3.3 V, or 5 V USB or the external VBAT as the supply voltage for the daughterboard.
The daughterboard contains numerous jumpers and test points for easy evaluation of the board. Also included with the kit are two current probes that can be plugged directly into jumper heads to measure currents with current probes.
主要特性：
Input voltage 2.7 V to 5.5 V
Boost solution supports up to 12 V
Evaluates 1 to 4 LED solutions
Configurable for 2-bit logic or I2C
|
没有任何评论
*只显示最新10条评论。评论内容只代表网友观点，与本站立场无关。 更多评论
|
|
发帖须知：
一.所发文章必须遵守《互联网电子公告服务管理规定》;
二.严禁发布供求代理信息,公司介绍,产品信息等广告宣传信息;
三.严禁恶意重复发帖;
四.严禁对个人,实体,民族,国家等进行漫骂,污蔑,诽谤。 |
|
|
|
当前位置：
首页 >> 行业应用 >> 电源系列 >> 解决方案
相关文章
发表评论